BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
- This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd.
- The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place.
- Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
- This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps.
- What you will get: 1 X BN-180 GPS Module
Brand : Geekstory
Category : Electronics,GPS, Finders & Accessories,GPS System Accessories,Antennas
Rating : 4.5
Price : US $25.99
Review Count : 117
BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
- The media could not be loaded. See attached pictures. The BN180 is installed under the propellers of the 250-gram drone. Even then, satellite reception is perfect without any glitches in the video. The weight of the GPS unit with wires is less than 6 grams, perfect for 250-gram FPV applications.
- If you are building an FPV drone using betaflight, this is the GPS you want right here.The only negative is the SUPER CHEAP wiring harness with the melt-away insulation. Why can\'t they give us a silicone wire harness? To save .01?
- You need to make sure it\'s literally on the window if you wish to get any data at all. It is very sensitive to position and will take a while to lock-on even if put in a good place. This makes it difficult to guess where to have it. I once put it near the window, waited 15 mins and nothing. I moved it two inches then it worked two minutes later.With that in mind, it can get really frustrating when you turn it off and on and slightly disposition it especially because it has no memory at all. Any locking it might have done earlier will be lost once it powers off.Apart from that, it serves my purpose. The NMEA statements are clear and they come up in a format easy to read.
- Lack of instructions leads you to googling. Very slow to sync at first. Lights and lack there of for 15 minutes was normal on first cold start. Check wires and be patient. Second boot was much better. Still have not checked update rate vs position but will update this review if not satisfied for a fpv quad.
- I\'ve tried a bunch of affordable ublox m8n units and this is my favorite. I put it on my r/c wings with arduplane and get 15-20 satellites most of the time, sometimes more. I\'d give it five stars if the antenna didn\'t detune so easily. If you use it for a fixed application this won\'t be a problem, but planes get bumped when you land and after a while this may detune the antenna a bit. Still, highly recommended.
- I had this for a few weeks. It worked fine. It was able to pick up GPS and GLONASS satellites reasonably quick (much faster than a NEO6M). When I used with the u-blox configuration settings, it worked with that program and I was able to change baud-rate and other parameters. It would save the settings on reboot. However, after a few minutes, it would default back to the default settings. I am building an Arduino based system that requires a high baudrate and refresh rate, this was very frustrating and I am going to choose another GPS module now. It does work fine at default settings, but do not expect any customization with this product.
- I like everything about this GPS receiver. For GPS receiver under $20 I give 5 stars. It has two working status LEDs, one for satellite FIX and NMEA sentence transmit cycles, the connector and the extra cables are the best I have seen so far. I bought a total of 21 for my business project and I plan on buying more.
- Not as good as the M8N module. Took a long time to get satellites and oftentimes didn’t get enough to arm the drone. I’d recommend the M8N over these.
Post a Comment for "BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory"